Rotary evaporators use new technology to increase recovery

Shanghai Xinzhuang Instrument Co., Ltd. has first-class technicians and a good team of technicians. It has advanced technology and strong development strength. Since its establishment, the products and services have been recognized by customers and have a good reputation. The company adheres to "integrity. Professional "Innovation. Growth" business philosophy to provide customers with meticulous service.
After the vacuum pump is turned on and the vacuum pump is turned on, it is found that the vacuum is not sealed. Check whether the bottle mouth is well sealed, whether the vacuum pump itself leaks, whether the sealing ring at the shaft is placed intact, and a vacuum switch connected in the external vacuum tube can improve the recovery rate and Evaporation rate.
The feeding uses the system vacuum negative pressure, and the liquid material can be sucked into the rotating bottle by the hose at the feeding port, and the liquid material should not exceed half of the rotating bottle. The instrument can be continuously fed, and attention should be paid when feeding. 1. Turn off the vacuum pump 2/stop heating 3. After the evaporation stops, slowly open the tube cock to prevent backflow.
Heating the instrument with a specially designed water bath must be energized after adding water. The temperature control scale is 0-99 °C for reference. Due to the existence of thermal inertia, the actual water temperature is about 2 degrees higher than the set temperature. The set value can be corrected when used. For example, you need water temperature 1/3-1/2. Use the connector to remove the power plug.
Rotate to open the electric control box switch and adjust the knob to the optimal evaporation speed. Take care to avoid fluctuations in the water bath and turn on the cooling water.
Recycle the solvent first, open the feed switch to deflate, then turn off the vacuum pump and take out the solvent in the collection bottle.
Precautions â—† The equipment should be coated with a layer of vacuum grease before installation, sealing surface seals and joints before installation.
â—†The heating tank must be filled with water before it is energized. It is not allowed to dry without water.
â—†RE-201D must be screwed into the fuse hole (19) to avoid damage to the flask.
â—† If the vacuum cannot be pumped up, check it:
1 Each joint, whether the interface is sealed 2 sealing ring, whether the sealing surface is effective 3 Whether the vacuum grease between the main shaft and the sealing ring is coated 4 Whether the vacuum pump and its leather tube are leaking 5 Whether the glass piece has cracks, chipping or damage

Maintenance leakage of the rotary evaporator is a common failure phenomenon of the evaporator, and frequent leak detection should be taken during use. Phenolphthalein test paper can be used for the leak, because ammonia is alkaline, and the phenolphthalein test paper turns red. When you look at it, the place where it is not frosted somewhere in the evaporator is the leak point. You can also find the leak with soapy water at the leak. Fluorescent evaporator leaks can be checked using halogen lamps and halogen leak detectors, or soapy water can be used to find leaks. When inspecting, first use the eye to evaporate the tube with oil traces. Because Freon and oil can be mutually soluble, when Freon leaks, it will also seep out from the leak. The company has first-class technicians and a good team of technicians. It has advanced technology and strong development strength. Since its establishment, the products and services have been recognized by customers and have a good reputation. The company adheres to the principle of "integrity, professionalism, innovation and growth." "The business philosophy provides customers with meticulous service.

Shanghai Xinzhuang follows the policy of “survival by quality, development by technology, efficiency by management, and credibility by service”. Every step of equipment, every project, every link, welcome you to buy!

Truck Mounted Crane is also called crane truck,boom truck, lorry Truck Crane, we offer a wide variety of truck mounted cranes for sale, we have telescopic boom truck cranes and folding boom truck cranes for sale, the crane brand could option XCMG,Sany, Unic, alfinger, and Hyva. and these brands of cranes could be mounted on the following chassis: Isuzu, Dongfeng, Sinotruk, Foton, FAW, JAC, BEIBEN...

Our boom truck lifting capacity available from 2 ton to 16 tons,we offer the best truck mounted crane price for clients , also provide one year warranty.                                                                                                                                                                                                                                                           

Truck Mounted Crane

Truck Mounted Crane,Truck Crane,Truck Loader Crane,Truck Loading Crane

Hubei Jiangnan Special Automobile Co., Ltd , https://www.dingshunglass.com