Gravure drawing failure troubleshooting

Drawing is one of the common problems in gravure printing, involving gravure printing machines, plate cylinders, doctor blades, and printing environments. Many factors such as ink, such as improper handling will affect the production and quality.

Drawing is also called pull line, starting line, when the ink performance and ink color is different, its performance is also different, usually black, blue. The drawing phenomenon of magenta is obvious, and it usually appears on a large area of ​​shallow web.

The common wire drawing is mainly divided into three types: drawing in the shallow position, drawing in the squeegee in the solid color, and drawing in the blank in the printing blank.

Shallow wire position drawing

1. From the origin of the design plate to prevent wire drawing

   Take full account of printability in manuscript design and plate making. As shown in Figure 1a, the printing direction must be taken into consideration, and printing from light to dark should be avoided as much as possible; Figure 1b and Figure 1c are relatively difficult due to the difficulty of the printing operation, and the design should also be considered as a factor. Black and magenta versions are most likely to appear on shallow webs, especially black ones. Due to the coarse carbon particles in the ink, when a black net is very shallow, a dot can hardly contain one carbon particle, so drawing is more likely to occur. Therefore, a large area of ​​black shallow net should be set as a special gray version, reducing the difficulty of printing and reject rate.


2. Correct use of squeegee to avoid drawing

(1) The selection of the squeegee. Chrome plate roller surface hardness of HV850 ~ 1100, the hardness of the squeegee should be lower than the plate hardness, about HV600 or so, the hardness is too low ink scraping is not clean, the hardness is too high will accelerate the printing plate wear. And will produce knife marks, affect the quality of printed products.

(2) The flatness of the squeegee. When the squeegee is installed, the blade should be flattened first, and then the screws should be tightened from the middle to the two sides in order. It cannot be reached in one step. It needs to be repeated two or three times to ensure that the blade is evenly loaded.

(3) The sharpness of the squeegee. The 600# water sandpaper or 2# metallographic sandpaper can be used to grind the squeegee, or use a special grinder to grind the back of the squeegee into a bevel of about 25°, even if a new knife is used.

(4) Squeegee angle. The squeegee angle is smaller than normal when printing, and at the same time, the distance between the squeegee and the plate contact point and the imprinting point is shortened.

3. Reasonably matching ink to prevent wire drawing

(1) When the screen has a large area of ​​shallow net or level transition, good quality ink should be used to prevent the ink pigment particles are too thick to cause drawing, usually the fineness of the ink is 15μm, too coarse ink particles to the squeegee The printing plate has a lot of damage.

(2) When dispensing ink, under the premise of no influence on other patterns on the same plate, consider using a slow-drying solvent. Do not add too much auxiliary solvents such as ethyl acetate to prevent the ink from changing and being unable to perform normal operations. print.

(3) Ensure that the ink viscosity is moderate and stable. The generation of drawing has a direct relationship with the viscosity of the ink. In general, the higher the viscosity of the ink, the easier it is to produce a knife line during printing. In addition, due to the different performance of each brand of ink, the amount of solvent added is not the same, the ink can be mixed with reference to the specific data provided by the manufacturer, and combined with their own printing conditions and the printed product for specific operations.

Field block color drawing

The drawing of the real color block from the knife position is shown in Fig. 2. The performance is due to the edge of the solid color block due to the lifting of the squeegee, causing the edge of the printing color block to appear broken line, generally a few millimeters of short fiber, the main reason is that the ink viscosity is too large and there is excessive pigment particle crystallization in the ink. Caused. The solution is as follows.

1. Filter the ink and add a certain amount of new ink during use.

2. Adjust the squeegee angle to be smaller, and shorten the distance between the squeegee blade's point of contact with the plate and the embossed point.

Irregular drawing of blank spaces

The irregular drawing of the blank space in the printing is an irregular ink path that is sometimes absent and has a short duration. It's usually thick. The causes and solutions are as follows.

1. The squeegee blade or knife has foreign objects stuck on it. It is possible to move the squeegee forward and backward and up and down during the printing process to remove the sticking foreign matter or remove it with a bamboo stick directly on the squeegee blade (must be completed by a skilled operator to avoid unnecessary loss due to improper operation) If necessary, stop the squeegee thoroughly.

2. Insufficient ink circulation. Part of the ink in the ink tank dead space, due to not get a good circulation caused by resin precipitation, the formation of different sizes of crystals and agglomeration, or excessive drying caused the formation of the surface of the ink (summer easy to produce ink, spring and autumn because the temperature There are many cases of ink crystallization and agglomeration. As the ink is circulated, a part of the ink is crystallized or the plate roller is rotated to the blade edge, and the squeegee breaks it to form a random wire drawing. Therefore, improvements must be made in both the circulation and filtration of the ink.

(1) Cycle improvement. The first method is to tilt the ink tank to the left or right to ensure that the ink can be injected from the slightly higher end and flow out from the lower end to form a good circulation: Method Two, the ink tank is laid flat, but the ink must be injected from both ends simultaneously. In the middle of the reflow, it can also form a very good cycle, can not be injected from the single side of the ink.

(2) Filter improvement. Before the ink is used, it must be filtered for the first time. Even new ink must be filtered. A 140 mesh/inch filter is generally used. The filtration work of the ink circulating in the ink tank is more important. It can well filter out the resin crystals and foreign impurities formed during the use of the ink. The mesh selected should be finer. The method is to set a stocking under the ink fountain. , Form a filter bucket, after filtering for a period of time, if the filter is blocked, ink flow is not smooth, you can insert some holes in the top of the bucket with a bamboo stick to increase the ink-conducting effect. The lower part of the bucket can also be used. The role of good deposition of impurities is shown in Figure 3. Some large printing plants in Shanghai and Guangdong have used this method to control intermittent ink drawing problems.

3. Ink fatigue. This situation occurs mostly when the printing area of ​​the printing plate is relatively small. During the printing process, the resin in the ink is continuously consumed. If the solvent is continuously added without adding new ink, the resin will not be replenished, and the proportion of each component of the ink will change, thus causing ink fatigue and affecting normal use. Appropriately adding new ink will solve the problem.

Other forms of brushed

1. Wire drawing caused by printing plate

(1) Surface treatment of printing plates. Gravure is now mostly electronically engraved. During the carving process, many small burrs are formed on the edge of the engraved mesh cavity. These small burrs also damage the squeegee during the printing process, causing the wire drawing. However, this type of drawing is limited to the dots on the printing plate and will not extend into the blank space. The new version is prone to this situation. Within a certain range, with the increase in the number of prints, drawing will gradually decrease. This requires that in the production process of the plate cylinder, on the one hand, the hardness of the engraved copper layer should be ensured, the formation of small burrs in the engraving process should be reduced, and the copper layer should be processed after the engraving; on the other hand, a standardized chromium layer should be established. Polishing process, including the type of belt used, the speed of the platen, the frequency of the polishing head, and the speed of movement. Polishing time and so on. If wire drawing occurs during the printing process, the surface of the printing plate can also be polished with 2# metallographic sandpaper or 600# water sandpaper or a dedicated nylon polishing net. Polishing can generally solve the drawing problem.

(2) Installation of printing plates. If the printing plate runs large during the printing process, it may also cause wire drawing. This requires checking the concentricity of the printing plate and the printing plate shaft (no shaft mounting plate to check the top), checking whether the bearing and transmission parts are deformed, worn, or even the machine base is horizontal.

2. Environmental wire drawing

The printing site environment must be kept clean. If there is dust in the operating environment, it may be mixed into the ink, resulting in drawing. Therefore, in the printing operation site, the number of people should be reduced as much as possible, and commuting should be performed in a clean and hygienic manner. Conditional companies can isolate the printing units, install air-conditioning facilities and dust removal equipment.
Drawing is one of the common problems in gravure printing, involving gravure printing machines, plate cylinders, doctor blades, and printing environments. Many factors such as ink, such as improper handling will affect the production and quality.

Drawing is also called pull line, starting line, when the ink performance and ink color is different, its performance is also different, usually black, blue. The drawing phenomenon of magenta is obvious, and it usually appears on a large area of ​​shallow web.

The common wire drawing is mainly divided into three types: drawing in the shallow position, drawing in the squeegee in the solid color, and drawing in the blank in the printing blank.

Shallow wire position drawing

1. From the origin of the design plate to prevent wire drawing

Take full account of printability in manuscript design and plate making. As shown in Figure 1a, the printing direction must be taken into consideration, and printing from light to dark should be avoided as much as possible; Figure 1b and Figure 1c are relatively difficult due to the difficulty of the printing operation, and the design should also be considered as a factor. Black and magenta versions are most likely to appear on shallow webs, especially black ones. Due to the coarse carbon particles in the ink, when a black net is very shallow, a dot can hardly contain one carbon particle, so drawing is more likely to occur. Therefore, a large area of ​​black shallow net should be set as a special gray version, reducing the difficulty of printing and reject rate.


2. Correct use of squeegee to avoid drawing

(1) The selection of the squeegee. Chrome plate roller surface hardness of HV850 ~ 1100, the hardness of the squeegee should be lower than the plate hardness, about HV600 or so, the hardness is too low ink scraping is not clean, the hardness is too high will accelerate the printing plate wear. And will produce knife marks, affect the quality of printed products.

(2) The flatness of the squeegee. When the squeegee is installed, the blade should be flattened first, and then the screws should be tightened from the middle to the two sides in order. It cannot be reached in one step. It needs to be repeated two or three times to ensure that the blade is evenly loaded.

(3) The sharpness of the squeegee. The 600# water sandpaper or 2# metallographic sandpaper can be used to grind the squeegee, or use a special grinder to grind the back of the squeegee into a bevel of about 25°, even if a new knife is used.

(4) Squeegee angle. The squeegee angle is smaller than normal when printing, and at the same time, the distance between the squeegee and the plate contact point and the imprinting point is shortened.

3. Reasonably matching ink to prevent wire drawing

(1) When the screen has a large area of ​​shallow net or level transition, good quality ink should be used to prevent the ink pigment particles are too thick to cause drawing, usually the fineness of the ink is 15μm, too coarse ink particles to the squeegee The printing plate has a lot of damage.

(2) When blending inks, consider using slow-drying solvents and not adding too much, without affecting other patterns on the same plate.

Auxiliary Equipment

Auxiliary Equipment,Moulding Machine ,Extruder Machine ,Plastic Packaging

Screen Printer Co., Ltd. , http://www.china-printing-machine.com